1993 Ford F-350 Transmission

Part Notes: Plug - rubber - located in bottom of transmission converter housing

Part Notes: (QQ-94-A) ring (7B067 to 7D392) retaining 4 17/32" I.D. - 1/16" thick

Part Notes: Located on both sides of 7D006 - 3 tabs (15.0-15.5mm) - used with 3 pinion planetaries
Washer - thrust - plain style - 3 tabs (15.0-15.5mm) - located between 7B067 and 7A398 - used with 3 pnion planetaries

Part Notes: Located on both sides of 7D006 planet - used with 4 pinion planetaries
Washer - thrust - plain style - located at between 7B067 and 7A398 - used with 4 pinion planetaries

Part Notes: (QQ-92-JJ) - ring (retain 7A527 cyl.) retainer - 1 59/64"

Part Notes: Forward clutch - 4 25/32" I.D. - flair lip seal

Part Notes: 11/32" thick - 5 1/8" I.D. - 26 teeth
Direct drive clutch, forward clutch rear
Rear - 11/32" thick - 5 1/8" I.D. - 26 teeth

Part Notes: Forward clutch front - triangle depression on face of plate
Front - 19/64" thick - 5 1/8" I.d. - 26 teeth

Part Notes: .118" tooth thickness - 5.640/5.630 OD - use w/FOSZ 7F207-A stl. stmp. cyl. only - 10 plate cl.

Part Notes: (QQ-92-J) - ring (7F235 to 7F283) retaining 1 19/32"

Part Notes: Forward clutch hub to reverse clutch gear. Forward sun gear to reverse clutch gear 2 7/32" O.D. x 1 29/64" I.D. x 1/4" thick

Part Notes: 3 3/4" dia - 3/64" thick
3 3/4" dia. x 3/64" thick

Part Notes: #8c Thrust
2 3/16" I.D. x 2 7/8" O.D.

Part Notes: Located between 7B067 and 7A398 planet - Located between 7A398 and 7D063 sun gear

Part Notes: 5/16" - Used without cooler bypass tube - use 7G118 & 7Z152 if equipted with cooler bypass tube

Part Notes: (QQ-97) - 7" O.D. - .085" thick, retaining ring - 7B066 to cyl.
(QQ-97) 7" O.D. - .085" thick, retaining ring 7B066 to 7D044

Part Notes: Apply side - 3.13-3.23mm Thick - 157.2-157.8mm I.D. - 26 teeth in a 30 tooth profile

Part Notes: Note: If connector requires replacement use 14A464 kit as cataloged., Includes Trans Fluid Temp Sensor

Part Notes: Plug - to block OSS/TSS hole in late E4OD service cases

Part Notes: Plug - speedometer hole, 4x2
Speed: All

Part Notes: Internal - friction - #1/16" thick and black dye stripe 1/4" to 1/2" wide
Internal - friction All

Part Notes: External - steel - 5 41/64" O.D. - 34 teeth - Use w/7F207-A stl. stamp. fwd. cl. cyl. plate not part of 7C391 kit - order plate separately

Part Notes: Hub only - used with E9TZ 7D171-AA and E6DZ 7G178-A

Part Notes: Includes "O" ring, 1/2 - 20 female x 1/4 NPTF male, for 5/16 diameter tube

Part Notes: #Ltrs.AODI stmp. on piston-Use w/F2TZ 7D044 A stl.drum only

Part Notes: (AB-91-E) bolt (7A103 to 7005) M8 x 1.25 x 65 hex head (metric)

Part Notes: Kit - drain plug in pan - includes reusable gasket, filter, 20 bolts, and I.S., All DSO applications only

Part Notes: 2" I.D. x 2 3/4" O.D.
Small - 2" I.D. x 2 3/4" O.D.

Part Notes: O-ring - pump outer seal - 9 33/64" O.D. - green, yellow or orange stripe

Part Notes: Direct clutch - 4 7/32" I.D. - flair lip seal

Part Notes: 7/32" thick - 34 teeth - 3 21/32" ID x 5.0" OD 12 plate clutch - use w/7F283 stl. stmp. cyl. only

Part Notes: External steel-32 teeth-.0665 thick-use w/F2TZ 7D044 A stl.stmp. drum only-not part of 7C391 kit- order separately

Part Notes: Internal - friction
Internal friction

Part Notes: Rear , 1 7/16" I.D. x 2" O.D. , (use as forward planet thrust bearing race)

Part Notes: 1 11/16" I.D. x 2 7/8" O.D., All 2/W/D
2/W/D

Part Notes: BEFORE 5/1/97
Race , used with E6DZ 7G178,A #9 thrust washer

Part Notes: (U-3-A) screw and washer (7H183 to 7A039) 1/4-20 x 0.62, 2/W/D

Part Notes: #9 Thrust Bearing
2 13/16" O.D. - located between 7D164 hub and 7D171 race
Located between 7A658 shaft and 7A130 support

Part Notes: (Q-6-G) - ring (7D164 to 7060) retaining 1 13/16"