How to Service and Repair Rear Coil Springs on Mercury Mariner?

Place the vehicle on a hoist which should be in neutral mode to begin servicing and repairing the rear coil spring. The first step involves supporting the wheel knuckle then unfastening its upper ball joint nut before removing the lower shock absorber nut along with its washer and bolt. The service requires removal of the upper arm inner bolt followed by loosening the lower arm inner bolt. The coil spring insulator and coil spring position needs documentation for later reinstallation then the wheel knuckle support needs gentle lowering before coil spring removal. First position the coil spring correctly with the insulator before safely elevating the wheel knuckle support. Connect the upper arm inner bolt then apply torque to both the upper as well as the lower arm inner bolts to 115 Nm (85 ft. lbs.). Attention should be given to tightening the lower shock absorber nut to 175 Nm (129 ft. lbs.). Install the lower shock absorber bolt with its washer followed by the bolt installation. During installation fit and tighten the upper ball joint nut before removing the wheel knuckle support at 76 ft. lbs (103 Nm).

How to Remove and Replace Coil Springs in the Front Suspension Strut and Spring Assembly on Mercury Mariner?

Start with theundle at each end of the coil spring in the all front suspension units by first unlocking the steering wheel and then removing both wheel and tire. To remove the brake jounce hose clip from its bracket users should pull the hose downward and place it aside. The next procedure requires removal of the wheel speed sensor harness bolt. You should use the hex-holding feature on the ball stud to stop its rotation before getting rid of the stabilizer bar link upper nut. First mark the positions of the four strut upper bushing plate nuts before removing these bolts, and the two strut-to-knuckle nuts and bolts. Then discard them all. The tripod constant velocity (CV) joint faces risk of damage when you prevent the axle shaft from extending outboard before uninstalling the strut and spring assembly. Service information contains the required details on strut assembly and disassembly procedures. When installing position the upper mounting plate into the inner fender while aligning new strut upper bushing nuts with reference marks before torquing them to 47 Nm (35 lb-ft). Install new strut-to-knuckle bolts and nuts while applying torque to 115 Nm (85 lb-ft) before completing the new upper stabilizer bar link nut that requires 63 Nm (46 lb-ft). Screw the wheel speed sensor harness bolt while tightening it to 15 Nm (133 lb-in). After that, direct the brake jounce hose back to the bracket before installing the clip. After final inspection you should perform an adjustment on the front end alignment.

OEM Mercury Mariner Coil Springs

Strut Spring

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

27 Coil Springs found

View related parts
Mercury Mariner Coil Spring, Front Part Number: 9L8Z-5310-E
$56.37 MSRP: $77.98
You Save: $21.61 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 9L8Z-5310-B
$55.45 MSRP: $76.72
You Save: $21.27 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 9L8Z-5310-D
$56.37 MSRP: $77.98
You Save: $21.61 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 9L8Z-5310-A
$55.45 MSRP: $76.72
You Save: $21.27 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 9M6Z-5560-D
$62.83 MSRP: $86.92
You Save: $24.09 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Manufacturer Note: Coil Springs
- Position: Rear
- Replaces: 9M6Z-5560-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 9M6Z-5560-C
$63.08 MSRP: $87.27
You Save: $24.19 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Manufacturer Note: Coil Springs
- Position: Rear
- Replaces: 9M6Z-5560-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 9L8Z-5560-D
$61.02 MSRP: $84.42
You Save: $23.40 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Manufacturer Note: Coil Springs
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 5L8Z-5310-A
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 5L8Z-5560-AA
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Mariner | Base, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Spring, Rear Part Number: 5L8Z-5560-CA
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Mariner | Base, Convenience, Luxury, Premier | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 5L8Z-5560-EA
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs
- Manufacturer Note: Coil Springs
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2006 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 5M6Z-5310-AB
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Position: Front
- Replaces: 5M6Z-5310-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008, 2006 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 7L8Z-5310-B
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Manufacturer Note: Spring code B
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 7L8Z-5310-E
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Manufacturer Note: Spring code E
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Front Part Number: 7L8Z-5310-F
Product Specifications
- Other Name: Spring - Front; Coil Spring, Front; Coil Springs; Spring
- Manufacturer Note: Spring code F
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 8L8Z-5560-B
Product Specifications
- Other Name: Spring - Rear; Coil Springs; Spring
- Manufacturer Note: Spring code E
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Mercury Mariner | Base, Convenience, Hybrid, Luxury, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 8L8Z-5560-C
Product Specifications
- Other Name: Spring - Rear; Coil Springs; Spring
- Manufacturer Note: Spring code F
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 8M6Z-5560-A
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Manufacturer Note: Spring Code 5M
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 9L8Z-5560-B
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Mariner Coil Spring, Rear Part Number: 9L8Z-5560-C
Product Specifications
- Other Name: Spring - Rear; Coil Spring, Rear; Coil Springs; Spring
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2011 Mercury Mariner | Base, Hybrid, Premier | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 27 Results

Mercury Mariner Coil Springs

OEM Coil Springs boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Coil Springs with long life and a perfect fit. Come to our website and find genuine Mercury Mariner parts. We keep a wide inventory of OEM Mariner parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Coil Springs used in Mercury Mariner automobile provide support for the load of the car and cushion the weight of the vehicle to avoid sinking and other unfavorable road conditions. Some of the signs that depict worn springs comprise ununiform wearing of tire treads and incorrect relative height if they determine the wheels alignment. Replacement springs are available in top specification, Variable rate spring, or the Cargo Coils for those with heavy cargoes. Performance coil springs enhance the performance of cars by minimizing the body roll and increasing the car's tractive capacity. Variants of the given coil springs include linear rate coil springs, progressive coil springs, and the dual rate coil springs; they exhibit rack and ride rate differences. Telescopic shock absorbers or height adjustable dampers are better because they enable one to change the height of the car in small steps without having to change the complete kit of lowered suspension.

Mercury Mariner Coil Springs Parts and Q&A

Coil Spring, Rear
5L8Z-5560-EA
Q: How to Service and Repair Rear Coil Springs on Mercury Mariner?
A:
Place the vehicle on a hoist which should be in neutral mode to begin servicing and repairing the rear coil spring. The first step involves supporting the wheel knuckle then unfastening its upper ball joint nut before removing the lower shock absorber nut along with its washer and bolt. The service requires removal of the upper arm inner bolt followed by loosening the lower arm inner bolt. The coil spring insulator and coil spring position needs documentation for later reinstallation then the wheel knuckle support needs gentle lowering before coil spring removal. First position the coil spring correctly with the insulator before safely elevating the wheel knuckle support. Connect the upper arm inner bolt then apply torque to both the upper as well as the lower arm inner bolts to 115 Nm (85 ft. lbs.). Attention should be given to tightening the lower shock absorber nut to 175 Nm (129 ft. lbs.). Install the lower shock absorber bolt with its washer followed by the bolt installation. During installation fit and tighten the upper ball joint nut before removing the wheel knuckle support at 76 ft. lbs (103 Nm).
Coil Spring, Front
9M6Z-5310-A
Q: How to Remove and Replace Coil Springs in the Front Suspension Strut and Spring Assembly on Mercury Mariner?
A:
Start with theundle at each end of the coil spring in the all front suspension units by first unlocking the steering wheel and then removing both wheel and tire. To remove the brake jounce hose clip from its bracket users should pull the hose downward and place it aside. The next procedure requires removal of the wheel speed sensor harness bolt. You should use the hex-holding feature on the ball stud to stop its rotation before getting rid of the stabilizer bar link upper nut. First mark the positions of the four strut upper bushing plate nuts before removing these bolts, and the two strut-to-knuckle nuts and bolts. Then discard them all. The tripod constant velocity (CV) joint faces risk of damage when you prevent the Axle Shaft from extending outboard before uninstalling the strut and spring assembly. Service information contains the required details on strut assembly and disassembly procedures. When installing position the upper mounting plate into the inner fender while aligning new strut upper bushing nuts with reference marks before torquing them to 47 Nm (35 lb-ft). Install new strut-to-knuckle bolts and nuts while applying torque to 115 Nm (85 lb-ft) before completing the new upper stabilizer bar link nut that requires 63 Nm (46 lb-ft). Screw the wheel speed sensor harness bolt while tightening it to 15 Nm (133 lb-in). After that, direct the brake jounce hose back to the bracket before installing the clip. After final inspection you should perform an adjustment on the front end alignment.