How to Service and Repair the Motor and Transmission Mount on a 6F50 on Lincoln MKS?

Initiate transmission mount repair of 6F50 vehicles by hoisting them to neutral position. The service starts with unfastening two Y-pipe nuts and separating the exhaust hanger for eventual disposal of the exhaust seal and its gasket and nuts. Remove the 4 nuts from the Y-pipe assembly before discarding the attached exhaust seals. Rotation of the engine roll restrictor-to-subframe through bolt should begin first before removing the 2 roll restrictor bracket bolts. The installation process for both the Mass Air Flow (MAF) sensor electrical connector and the engine breather from the Air Cleaner (ACL) assembly involves their disconnection. Untighten the outlet pipe clamp at the throttle body while removing the bolts from the ACL assembly bracket and taking out both the ACL and ACL outlet pipe assembly. Disassemble the battery while taking out its power supply and unplugging all harnesses from the battery tray. To remove the battery tray and bracket first unfasten the lower bracket bolts at two positions and the upper battery tray bolt with its matching nut and separate the power distribution box fasteners. A floor jack should assist you in releasing transaxle support insulator pressure through careful installation of the oil pan holding fixture beneath the oil pan. First lower the transaxle from the mount about 50.8 mm (2 in) before removing its transaxle support insulator through bolt and flagnut. The procedure begins by removing four nuts along with the transaxle support insulator bracket before moving to the bottom and top bolts which detach the insulator bracket. Begin with the installation of bottom transaxle support insulator bolts through a torque of 55 Nm (41 lb-ft) and then move to the top bolts with the same torque value. The 4 bracket nuts must be torqued to 63 Nm (46 lb-ft) when securing the transaxle support insulator bracket. The floor jack and oil pan holding fixture allow you to lift the transaxle so you can install its support insulator through bolt while tightening it to 175 Nm (129 lb-ft). Place the floor jack and oil pan holding fixture to the side before installing the battery tray along with its bracket while applying 9 Nm (80 lb-in) to the battery tray bolt and 9 Nm (80 lb-in) to the lower bracket bolts. Secure the five pin-type wiring harness fasteners onto the battery tray while installing the battery. Position the ACL assembly before you install its bracket bolts which should be tightened to 11 Nm (97 lb-in) then apply 5 Nm (44 lb-in) torque to the ACL outlet pipe clamp at the TB. Position the engine breather at both the MAF sensor electrical connector and the ACL assembly. Hang the roll restrictor before installing its bolts to 90 Nm (66 lb-ft) while after installing the through bolt to match that torque. To complete the last steps, you need to add new exhaust seals before moving the Y-pipe into position and installing 4 new exhaust Y-pipe assembly nuts with a torque setting of 40 Nm (30 lb-ft). This needs to be followed by installing the new exhaust seal and placing the Y-pipe in the exhaust hanger before tightening 2 new exhaust flange nuts to 40 Nm (30 lb-ft).

OEM Lincoln MKS Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Motor And Transmission Mounts found

View related parts
Lincoln MKS Motor Mount, Front Part Number: DG1Z-6038-E
$107.56 MSRP: $156.57
You Save: $49.01 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Front Mount; Mount
- Position: Front
- Replaces: DG1Z-6038-C, DG1Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Transmission Mount Part Number: GB5Z-6068-A
$49.08 MSRP: $70.22
You Save: $21.14 (31%)
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Support Rod; Engine Mount Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Torsion Arm
- Manufacturer Note: Rear
- Replaces: AA5Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2016 Lincoln MKS | EcoBoost | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKS Transmission Mount, Front Upper Part Number: DG1Z-6038-F
$66.30 MSRP: $96.50
You Save: $30.20 (32%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Front Upper; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount; Upper Trans Mount
- Position: Front Upper
- Replaces: DG1Z-6038-D, 8G1Z-6038-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2016 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Torsion Arm, Lower Part Number: 9G1Z-6068-A
$42.16 MSRP: $61.37
You Save: $19.21 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Automatic Transmission Mount, Lower; Engine Support Rod; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Lower Mount; Lower Trans Mount; Transmission Mount
- Position: Lower
- Replaces: 8G1Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Lower Trans Mount, Front Part Number: DA5Z-6068-C
$94.21 MSRP: $137.13
You Save: $42.92 (32%)
ADD TO CART
Product Specifications
- Other Name: Housing; Automatic Transmission Mount, Lower; Transfer Case Mount; Transmission Mount
- Position: Front Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Torque Arm Part Number: DA5Z-6068-B
$88.29 MSRP: $128.52
You Save: $40.23 (32%)
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Support Rod; Engine Mount Torque Strut; Motor Mount
- Manufacturer Note: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Front Mount Part Number: AA5Z-6038-D
$87.95 MSRP: $128.02
You Save: $40.07 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: AA5Z-6038-A, AA5Z-6038-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2016 Lincoln MKS | EcoBoost | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKS Transmission Mount, Upper Part Number: AA5Z-6038-B
$101.14 MSRP: $147.22
You Save: $46.08 (32%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Upper; Transfer Case Mount; Upper Trans Mount
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2016 Lincoln MKS | EcoBoost | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKS Front Mount Part Number: 8G1Z-6038-A
$76.38 MSRP: $111.18
You Save: $34.80 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount; Insulator
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2012 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Mount Bracket, Front Passenger Side Part Number: 8M8Z-6038-A
$63.73 MSRP: $97.90
You Save: $34.17 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Front Engine Mount Support; Right Engine Mount Bracket; Torque Strut; Motor Mount.; Engine Bracket; Front Mount; Front Mount Bracket; Support; Mount
- Manufacturer Note: Bracket
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2016 Lincoln MKS | Base, EcoBoost | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Mount Bracket, Upper Part Number: 8G1Z-6031-A
$51.90 MSRP: $74.25
You Save: $22.35 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount; Transfer Case Mount; Motor Mount; Transmission Mount Bracket; Transmission Mount
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2016 Lincoln MKS | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKS Front Mount Part Number: DA5Z-6038-A
$145.80 MSRP: $225.00
You Save: $79.20 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Motor Mount; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKS | EcoBoost | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKS Transmission Mount, Front Lower Part Number: AA5Z-6068-B
$73.58 MSRP: $107.10
You Save: $33.52 (32%)
Product Specifications
- Other Name: Automatic Transmission Mount, Lower; Engine Support Rods; Engine Mounts; Transfer Case Mount; Lower Trans Mount; Torsion Damper
- Position: Front Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2016 Lincoln MKS | EcoBoost | 6 Cyl 3.5 L GAS

Lincoln MKS Motor And Transmission Mount

OEM Motor And Transmission Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Lincoln's official factory standards. These steps remove flaws and inconsistencies. So you can get Motor And Transmission Mount with long life and a perfect fit. Come to our website and find genuine Lincoln MKS parts. We keep a wide inventory of OEM MKS parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Lincoln MKS Motor And Transmission Mount is one of the most important assemblies that underlines the Lincoln MKS line and its production quality. Intended to allow for the secure coupling of the motor to the transmission while at the same time, positioning it in such a manner that it is isolated from the vibrations of the engine, the Motor And Transmission Mount is a significant component in the stability, and functional cohesion of the transmission system of the automobile across different models of MKS manufactured between 2008 and 2016. Through successful vibrations absorption and reduction, the Lincoln MKS Motor And Transmission Mount works to improve the performance as well as the sturdiness of the car to provide a smooth ride. This is more due to the fact that it can fit into various types of the MKS structure rendering it a critical component of Lincoln MKS. Also, with the help of the Motor And Transmission Mounts, power is transferred efficiently and safely and there is less wear on the transmission. The Lincoln MKS Motor And Transmission Mount has certain features that make it stand out and these include; the ability of the mount to offer maximum support in the long-run while at the same time taking the rigors of everyday use on the road. Such attention is paid not only to the driving experience but also to the essence of Lincoln brand and its focus on luxurious and high-performance vehicles. In conclusion, Lincoln has been proud to present the Lincoln MKS Motor And Transmission Mount as one of its key highlights in the LVH&TM market to provide car users with the steady and hearty Lincoln MKS luxury car.

Lincoln MKS Motor And Transmission Mount Parts and Q&A

Transmission Mount, Front Upper
DG1Z-6038-F
Q: How to Service and Repair the Motor and Transmission Mount on a 6F50 on Lincoln MKS?
A:
Initiate transmission mount repair of 6F50 vehicles by hoisting them to neutral position. The service starts with unfastening two Y-pipe nuts and separating the exhaust hanger for eventual disposal of the exhaust seal and its gasket and nuts. Remove the 4 nuts from the Y-pipe assembly before discarding the attached exhaust seals. Rotation of the engine roll restrictor-to-subframe through bolt should begin first before removing the 2 roll restrictor bracket bolts. The installation process for both the Mass Air Flow (MAF) sensor electrical connector and the engine breather from the Air Cleaner (ACL) assembly involves their disconnection. Untighten the outlet pipe clamp at the Throttle Body while removing the bolts from the ACL assembly bracket and taking out both the ACL and ACL outlet pipe assembly. Disassemble the battery while taking out its power supply and unplugging all harnesses from the battery tray. To remove the battery tray and bracket first unfasten the lower bracket bolts at two positions and the upper battery tray bolt with its matching nut and separate the power distribution box fasteners. A floor jack should assist you in releasing transaxle support insulator pressure through careful installation of the Oil Pan holding fixture beneath the oil pan. First lower the transaxle from the mount about 50.8 mm (2 in) before removing its transaxle support insulator through bolt and flagnut. The procedure begins by removing four nuts along with the transaxle support insulator bracket before moving to the bottom and top bolts which detach the insulator bracket. Begin with the installation of bottom transaxle support insulator bolts through a torque of 55 Nm (41 lb-ft) and then move to the top bolts with the same torque value. The 4 bracket nuts must be torqued to 63 Nm (46 lb-ft) when securing the transaxle support insulator bracket. The floor jack and oil pan holding fixture allow you to lift the transaxle so you can install its support insulator through bolt while tightening it to 175 Nm (129 lb-ft). Place the floor jack and oil pan holding fixture to the side before installing the battery tray along with its bracket while applying 9 Nm (80 lb-in) to the battery tray bolt and 9 Nm (80 lb-in) to the lower bracket bolts. Secure the five pin-type wiring harness fasteners onto the battery tray while installing the battery. Position the ACL assembly before you install its bracket bolts which should be tightened to 11 Nm (97 lb-in) then apply 5 Nm (44 lb-in) torque to the ACL outlet pipe clamp at the TB. Position the engine breather at both the MAF sensor electrical connector and the ACL assembly. Hang the roll restrictor before installing its bolts to 90 Nm (66 lb-ft) while after installing the through bolt to match that torque. To complete the last steps, you need to add new exhaust seals before moving the Y-pipe into position and installing 4 new exhaust Y-pipe assembly nuts with a torque setting of 40 Nm (30 lb-ft). This needs to be followed by installing the new exhaust seal and placing the Y-pipe in the exhaust hanger before tightening 2 new exhaust flange nuts to 40 Nm (30 lb-ft).