How to Address Issues with the Motor and Transmission Mount on a Ford Ranger?

A complete repair or service of the transmission mount requires vehicle elevation and support before beginning the work. Before the removal of the rear driveshaft on a 4x2 configuration drivers should mark both the yoke and flange for driveshaft balance purposes. Once this is complete the driveshaft bolts could be removed and the driveshaft taken out of place. After removing the transmission mount nuts you should raise the transmission to reach the mount. Detach the transmission mount by removing its screws. Start by placing the transmission mount on the extension housing then fasten it with proper mount-to-extension hardware. Place the transmission mount into the crossmember then tighten the installing nuts via completion. Prior to lowering the vehicle position the driveshaft so that it stays aligned with the markings made for balance then install the bolts.

How to Service and Repair the Motor and Transmission Mount on Ford Ranger?

First service the vehicle in neutral position using a hoist while keeping in mind 4x4 models need front driveshaft removal before beginning. Identify and mark the points where the rear driveshaft yoke meets the axle flange for preserving the driveshaft equilibrium before removing its four bolts. Users should detach the rear driveshaft from the flange by applying a pry bar while maintaining hammer-free operation. You should begin by removing the transmission mount nuts followed by raising the transmission whereas you should remove the transmission mount. Finally, place the new transmission mount on the extension housing and fix it with screws while torquing them to reach 90 Nm (66 ft. lbs.). Install the transmission mount into the crossmember and fasten its nuts using the same torque values. The last step involves driving the driveshaft along the marks to check for balance before you put in the rear driveshaft and tighten its bolts to 103 Nm (76 ft. lbs.).

OEM Ford Ranger Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

53 Motor And Transmission Mounts found

View related parts
Ford Ranger Motor Mount, Driver Side Part Number: KB3Z-6038-J
$120.41 MSRP: $175.27
You Save: $54.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Motor Mount, Driver Side Part Number: KB3Z-6038-K
$122.55 MSRP: $178.38
You Save: $55.83 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Mount Bracket, Driver Side Part Number: 1L5Z-6031-CA
$50.88 MSRP: $72.78
You Save: $21.90 (31%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Left; Motor Mount; Engine Mount Bracket
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2011 Ford Ranger | Edge, FX4, Sport, STX, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Motor Mount, Driver Side Part Number: 1L5Z-6038-AB
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Left; Engine Mount Bracket; Front Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2011 Ford Ranger | Sport, STX, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Mount Bracket, Passenger Side Part Number: 2L5Z-6030-AB
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Right; Motor Mount; Engine Mount Bracket
- Manufacturer Note: RH , bracket, torsion bar suspension, FROM 9/25/01
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2008 Ford Ranger | Edge, Sport, STX, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Mount Bracket, Driver Side Part Number: 2L5Z-6031-AA
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Left; Motor Mount; Engine Mount Bracket
- Manufacturer Note: LH, torsion bar suspension, FROM 9/25/01
- Position: Driver Side
- Replaces: F87Z-6031-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2008 Ford Ranger | Edge, Splash, Sport, STX, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Motor Mount, Driver Side Part Number: 4L5Z-6038-BA
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Left; Engine Mount Bracket; Front Mount; Engine Mount
- Position: Driver Side
- Replaces: 2L5Z-6038-AA, 4L5Z-6038-AA, XL5Z-6038-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2011 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Mount Bracket, Driver Side Part Number: E5TZ6029B
Product Specifications
- Other Name: Bracket - Engine Support; Engine Mount Bracket; Motor Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1997 Ford Ranger | Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Wheel Seal Part Number: E5TZ-6068-G
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Rear Mount
- Replaced by: F5TZ-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1985-1991 Ford Ranger | Base, Custom, GT, S, S Plus, Sport, STX, XL, XLS, XLT | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L DIESEL, 4 Cyl 2.3 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Motor Mount Part Number: F47Z-6038-A
Product Specifications
- Other Name: Insulator Assembly; Engine Mount Bracket; Front Mount
- Manufacturer Note: RH AND LH
- Replaces: E5TZ-6038-V
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1997 Ford Ranger | Custom, S, S Plus, Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Transmission Mount Part Number: 7L5Z-6068-FA
$104.20 MSRP: $151.67
You Save: $47.47 (32%)
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount.; Rear Mount
- Replaces: 1L5Z-6068-BA, F87Z-6068-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2011 Ford Ranger | Edge, FX4, Splash, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Rear Mount Part Number: E9TZ-6A023-E
Product Specifications
- Other Name: Support; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Rear Insulator; Rear Support
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1989-1997 Ford Ranger | Custom, S, S Plus, Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Rear Mount Part Number: F1TZ-6068-A
Product Specifications
- Other Name: Insulator Assembly - Engine; Engine Mount Bracket; Motor Mount
- Replaced by: F5TZ-6068-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1986-1991 Ford Ranger | Base, Custom, GT, S Plus, Sport, STX, XL, XLT | 6 Cyl 2.9 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Mount Bracket, Driver Side Part Number: 2L5Z-6031-DA
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Left; Motor Mount; Engine Mount Bracket
- Manufacturer Note: LH, coil spring suspension, FROM 9/25/01-BEFORE12/02/02
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2004 Ford Ranger | Edge, Splash, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Mount Bracket, Passenger Side Part Number: 3L5Z-6030-HA
Product Specifications
- Other Name: Bracket; Engine Mount Bracket, Right; Motor Mount; Engine Mount Bracket
- Manufacturer Note: RH, coil spring suspension, FROM 4/28/03
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Ranger | Edge, Sport, STX, XL, XLT | 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Motor Mount, Passenger Side Part Number: 3L5Z-6038-AB
Product Specifications
- Other Name: Kit; Engine Mount Bracket, Right; Engine Mount, Right; Engine Mount Bracket; Mount Bracket; Front Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2004 Ford Ranger | Edge, Splash, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Motor Mount, Driver Side Part Number: 5L5Z-6038-AA
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount Bracket; Front Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Ranger | Edge, Sport, STX, XL, XLT | 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Motor Mount, Passenger Side Part Number: 5L5Z-6038-AB
Product Specifications
- Other Name: Insulator Assembly; Engine Mount Bracket; Front Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2008 Ford Ranger | Edge, Sport, STX, XL, XLT | 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Support Bar Part Number: 6L5Z-6A023-AA
Product Specifications
- Other Name: Support; Transmission Crossmember; Engine Mount Torque Strut
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2011 Ford Ranger | Edge, FX4, Splash, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Mount Bracket, Front Passenger Side Part Number: E5TZ6028D
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount Bracket; Motor Mount
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1997 Ford Ranger | Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS

| Page 1 of 3 |Next >

1-20 of 53 Results

Ford Ranger Motor And Transmission Mount

OEM Motor And Transmission Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Motor And Transmission Mount with long life and a perfect fit. Come to our website and find genuine Ford Ranger parts. We keep a wide inventory of OEM Ranger parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Motor And Transmission Mount is an important component in the Ford Ranger vehicles since it plays a crucial role of firmly fixing the transmission onto position and at the same time protect it from being affected by the vibrations of the engine. Depending on the type of transmission used in making the car, a Ford Ranger may contain one or more than one Motor And Transmission Mount for enhanced stability and performance. Hence, different styles of Motor And Transmission Mounts have been used in Ford Ranger vehicle in the past years depending on the type of configuration required. These mounts vary mainly by the design and the number of them to be installed and it has a great influence on the handling as well as on the comfort of the car. Functionality of the Motor And Transmission Mount is relevant in ensuring that the Ford Ranger's drivetrain remains stable besides improving on the handling feel.

Ford Ranger Motor And Transmission Mount Parts and Q&A

Motor Mount, Passenger Side
1L5Z-6038-AA
Q: How to Address Issues with the Motor and Transmission Mount on a Ford Ranger?
A:
A complete repair or service of the transmission mount requires vehicle elevation and support before beginning the work. Before the removal of the rear driveshaft on a 4x2 configuration drivers should mark both the yoke and flange for driveshaft balance purposes. Once this is complete the driveshaft bolts could be removed and the driveshaft taken out of place. After removing the transmission mount nuts you should raise the transmission to reach the mount. Detach the transmission mount by removing its screws. Start by placing the transmission mount on the extension housing then fasten it with proper mount-to-extension hardware. Place the transmission mount into the crossmember then tighten the installing nuts via completion. Prior to lowering the vehicle position the driveshaft so that it stays aligned with the markings made for balance then install the bolts.
Motor Mount, Driver Side
4L5Z-6038-BA
Q: How to Service and Repair the Motor and Transmission Mount on Ford Ranger?
A:
First service the vehicle in neutral position using a hoist while keeping in mind 4x4 models need front driveshaft removal before beginning. Identify and mark the points where the rear driveshaft yoke meets the axle flange for preserving the driveshaft equilibrium before removing its four bolts. Users should detach the rear driveshaft from the flange by applying a pry bar while maintaining hammer-free operation. You should begin by removing the transmission mount nuts followed by raising the transmission whereas you should remove the transmission mount. Finally, place the new transmission mount on the extension housing and fix it with screws while torquing them to reach 90 Nm (66 ft. lbs.). Install the transmission mount into the crossmember and fasten its nuts using the same torque values. The last step involves driving the driveshaft along the marks to check for balance before you put in the rear driveshaft and tighten its bolts to 103 Nm (76 ft. lbs.).