How to Service and Repair the Exhaust Pipe Downpipe for the 2.3L Engine on Ford Ranger?

Place the 2.3L vehicle for exhaust downpipe servicing by placing it on a hoist in neutral position. Disconnect the electrical connectors of both Heated Oxygen Sensor (HO2S) and Catalyst Monitor Sensor (CMS). Separate the exhaust downpipe from the muffler and tailpipe assembly through removal of two bolts and two flagnuts with a gasket that must be discarded. The exhaust manifold next to downpipe requires the removal of two retaining nuts before their disposal. You need to uninstall the transmission mount together with the isolator-to-transmission bolt to detach the exhaust downpipe. Installation should be carried out without oil or grease-based lubricants on isolators since rubber deterioration will occur. Clean every contact point on the exhaust downpipe before setting its proper position into the vehicle. Place the transmission mount with an isolator-to-transmission bolt installed and tighten it at 90 Nm (66 lb-ft). Fasten together two new exhaust downpipe-to-exhaust manifold nuts while tightening them to 40 Nm (30 lb-ft). After placing the exhaust downpipe-to-muffler and tailpipe assembly gasket follow the installation of two exhaust downpipe-to-muffler and tailpipe assembly bolts with two new flagnuts and tighten to 40 Nm (30 lb-ft). The final step requires reconnecting HO2S and CMS electrical connectors after which technicians should validate the exhaust system isolators maintain zero load position; additional exhaust system alignment must occur if zero load is not achieved.

OEM Ford Ranger Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Exhaust Pipes found

View related parts
Ford Ranger Front Pipe Part Number: KB3Z-5A212-C
$263.43 MSRP: $346.42
You Save: $82.99 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Extension - Exhaust Pipe; Exhaust Intermediate Pipe; Exhaust Pipe
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Catalytic Converter Part Number: KB3Z-5E212-F
$461.10 MSRP: $567.14
You Save: $106.04 (19%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Converter Assembly; Converter
- Replaces: KB3Z-5E212-A, KB3Z-5E212-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Front Pipe Part Number: F87Z-5246-AA
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Intermediate Pipe; Exhaust Pipe
- Manufacturer Note: Pipe asy. - muffler inlet without converters - 3.0L eng. - exc. Calif. -1998/2000
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: 1L5Z-5F250-AA
Product Specifications
- Other Name: Converter Assembly; Exhaust Intermediate Pipe; Catalytic Converter; Exhaust Pipe
- Manufacturer Note: Pipe asy. - 4x4 inlet pipe with catalyst - 3.0L - (catchword TUN) - 2001/2001
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: 1L5Z-5F250-CA
Product Specifications
- Other Name: Converter Assembly; Exhaust Intermediate Pipe; Catalytic Converter; Exhaust Pipe
- Manufacturer Note: Pipe asy. - 4x2 inlet pipe with catalyst - 3.0L exc. FFV - (catchword PAN) - 2001/2002 - BEFORE 8/06/01
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: 1L5Z-5F250-EA
Product Specifications
- Other Name: Converter Assembly; Exhaust Intermediate Pipe; Catalytic Converter; Exhaust Pipe
- Manufacturer Note: Pipe asy. - 4x2 inlet pipe with catalyst - 3.0L with FFV - 2001/2003
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: 2L5Z-5F250-AA
Product Specifications
- Other Name: Converter Assembly; Exhaust Intermediate Pipe; Catalytic Converter; Exhaust Pipe
- Manufacturer Note: Pipe asy. - inlet pipe with catalyst - 3.0L - (catchword RUN) - 2002/2003
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: 3L5Z-5230-AA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 112" WB - 2003 - FROM 12/02/02
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: 3L5Z-5230-BA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 118" WB - 2003 - FROM 12/02/02
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Ranger | XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: 3L5Z-5230-CA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 126" WB - 2003 - FROM 12/02/02
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: 3L5Z-5230-DA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 112" WB 2.5L, 3.0L & 4.0L - 2003 - FROM 12/02/02
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: 3L5Z-5230-EA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 118" WB 3.0L & 4.0L - 2003 - FROM 12/02/02
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: 3L5Z-5230-FA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 126" WB 3.0L & 4.0L - 2003 - FROM 12/02/02
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: 3L5Z-5F250-AA
Product Specifications
- Other Name: Converter Assembly; Exhaust Intermediate Pipe; Catalytic Converter; Exhaust Pipe
- Manufacturer Note: Pipe asy. - 4x2 inlet pipe with catalyst - 3.0L exc. FFV - (catchword RAF) - 2003 - FROM 12/02/02
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Ford Ranger | Edge, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: F3TZ-5246-B
Product Specifications
- Other Name: Pipe - Exhaust Front; Exhaust Pipe
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1993-1994 Ford Ranger | Splash, Sport, STX, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: F87Z-5230-AA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 112" WB - 1998/2000
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Muffler & Pipe, Rear Part Number: F87Z-5230-CA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Manufacturer Note: Muffler asy. - 126" WB - 1998/2000
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Inlet Pipe Part Number: F87Z-5246-BA
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Intermediate Pipe; Exhaust Crossover Pipe; Exhaust Pipe; Front Pipe
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: F87Z-5F250-BA
Product Specifications
- Other Name: Converter Assembly; Exhaust Pipe
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Front Pipe Part Number: F87Z-5F250-CA
Product Specifications
- Other Name: Converter Assembly; Catalytic Converter; Exhaust Pipe
- Manufacturer Note: Pipe asy. - muffler inlet with converters - 3.0L eng. - California - (catchword REK) - 1998/2000
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2000 Ford Ranger | Splash, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 23 Results

Ford Ranger Exhaust Pipe

OEM Exhaust Pipe boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Exhaust Pipe with long life and a perfect fit. Come to our website and find genuine Ford Ranger parts. We keep a wide inventory of OEM Ranger parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Ranger Exhaust Pipe is one of the most important parts that boosts the performance and durability of the Ford Ranger automobiles. An important component that links several parts of the exhaust system, including the manifold, the catalytic converter, as well as the muffler, the Exhaust Pipe plays a role as the exhaust gases' channel. This linkage becomes especially valuable for a number of Rose solemn models, let alone that it embraces all the generations of the Ranger, from the compact pickups of the early 1980s up to the mid-size trucks of 2019. A noteworthy feature is the Ford Ranger Exhaust Pipe mostly used to enhance the flow of exhaust hence the prospects of getting extra horsepower together with efficiency. Further, exhaust pipe is highly vulnerable to rust and physical damage; thus, exhaust pipes require durable replacements or upgrades. Mandrel-bent designs add places where specific bends are needed; they increase exhaust flow, making the unit both more effective and safer. This is further complimented by the Exhaust Pipe of Ford Ranger that is extensively needed in the functionality of the car in terms of efficiency and environmentalism. Due to its durability and unique design, the Ford Ranger Exhaust Pipe is capable of satisfying the needs of different models of the Ranger, and because of it, being an important element in the Ford model that will contribute to the safety of the ride and energy efficiency.

Ford Ranger Exhaust Pipe Parts and Q&A

Extension
4L5Z-5K238-AA
Q: How to Service and Repair the Exhaust Pipe Downpipe for the 2.3L Engine on Ford Ranger?
A:
Place the 2.3L vehicle for exhaust downpipe servicing by placing it on a hoist in neutral position. Disconnect the electrical connectors of both Heated Oxygen Sensor (HO2S) and Catalyst Monitor Sensor (CMS). Separate the exhaust downpipe from the Muffler and tailpipe assembly through removal of two bolts and two flagnuts with a gasket that must be discarded. The Exhaust Manifold next to downpipe requires the removal of two retaining nuts before their disposal. You need to uninstall the transmission mount together with the isolator-to-transmission bolt to detach the exhaust downpipe. Installation should be carried out without oil or grease-based lubricants on isolators since rubber deterioration will occur. Clean every contact point on the exhaust downpipe before setting its proper position into the vehicle. Place the transmission mount with an isolator-to-transmission bolt installed and tighten it at 90 Nm (66 lb-ft). Fasten together two new exhaust downpipe-to-exhaust manifold nuts while tightening them to 40 Nm (30 lb-ft). After placing the exhaust downpipe-to-muffler and tailpipe assembly gasket follow the installation of two exhaust downpipe-to-muffler and tailpipe assembly bolts with two new flagnuts and tighten to 40 Nm (30 lb-ft). The final step requires reconnecting HO2S and CMS electrical connectors after which technicians should validate the exhaust system isolators maintain zero load position; additional exhaust system alignment must occur if zero load is not achieved.