What are the crucial steps to take when servicing the front Air Bag Sensor involved in a crash on Ford Fusion?

Before servicing the front impact severity sensor one should check the restraints control module (RCM) as well as the impact sensor attachment points for deformities if the vehicle suffered crash damage. All production specifications for damaged areas should be restored to their original state before installing new RCM components and sensors without exception because inadequate installation could result in fatalities or severe injuries in a car accident. The restraints control module indicator should light up when the RCM fuse is removed while the ignition switch is ON because this represents correct behavior with no issues in the supplemental restraint system (SRS). A vehicle cannot be released for market unless the supplemental restraint system completes all operational checks with no detected faults. The diagnostic process requires part replacement as a first step towards repair; reinstalling the original part should follow and the diagnostic procedure must be executed again. Your first step should be to disable the SRS system before removing the 2 bolts along with 2 pin-type retainers from the upper grille. Operation of the restraint systems depend on tight fastener torque to correct specifications. Both components need thorough cleaning with no residue allowed prior to installing the front impact severity sensor and bracket assembly. Make note of the locator tab position for its later reinstallation. To proceed with this operation gently move the upper grille forward before removing the bolt securing the front impact severity sensor assembly while disconnecting its electrical connector for final removal of the assembly. First secure the bolt to 12 Nm (9 lb-ft) torque specification then enable SRS functions as the last step for installation.

How to service the Air Bag Sensor located in the B-pillar on Ford Fusion?

Service of the B-pillar side impact sensor begins with disabling the SRS system. The service begins by removing scuff plate trim pieces from both front and rear doors before sliding down the lower B-pillar trim to detach it from the upper B-pillar trim. Cut the electrical wire connection of the side impact sensor. The restraints control module RCM along with the impact sensor require proper torque tightening because this action improves restraint system performance which reduces crash-related injuries. Clean the mating surfaces on the B-pillar joint with side impact sensor while removing any foreign matter. Document the sensor position and its locating tab before reinstalltion. The bolt and side impact sensor need removal before installing a new sensor which must get tightened to 12 Nm (9 lb-ft). Repeated steps in reverse order will enable the installation of components followed by restart of SRS operation.

OEM Ford Fusion Air Bag Sensor

Air Bag Impact Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Air Bag Sensors found

View related parts
Ford Fusion Side Impact Sensor, Center Part Number: H2GZ-14B345-A
$57.66 MSRP: $88.57
You Save: $30.91 (35%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Impact Sensor, Center; Air Bag Sensor; Side Sensor
- Position: Center
- Replaces: DS7Z-14B345-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | Energi SE, Energi Titanium, S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Side Impact Sensor, Front Part Number: CT4Z-14B345-A
$34.63 MSRP: $49.12
You Save: $14.49 (30%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Impact Sensor, Center, Center Front, Front; Air Bag Sensor; Side Sensor
- Position: Front
- Replaces: AE9Z-14B345-A, DR3Z-14B345-B, AE9Z-14B345-B, DR3Z-14B345-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Fusion | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Fusion Impact Sensor, Rear Part Number: 9L3Z-14B345-A
$43.95 MSRP: $63.97
You Save: $20.02 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Impact Sensor, Center Front, Center Rear, Front, Rear; Air Bag Sensor; Front Impact Sensor; Front Sensor; Side Impact Sensor; Side Sensor
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2012 Ford Fusion | Hybrid, S, SE, SEL, Sport | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Rear Sensor, Front Part Number: HS7Z-14B004-A
$42.41 MSRP: $66.18
You Save: $23.77 (36%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; Air Bag Impact Sensor, Front, Rear; Air Bag Sensor; Impact Sensor; Front Impact Sensor; Front Sensor; Side Impact Sensor; Side Sensor
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Impact Sensor, Front Part Number: CP9Z-14B004-A
$85.88 MSRP: $144.18
You Save: $58.30 (41%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; Air Bag Impact Sensor, Front, Rear; Air Bag Sensor; Front Impact Sensor; Front Sensor; Side Impact Sensor; Side Sensor
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Ford Fusion | Energi SE, Energi Titanium, S, S Hybrid, SE, SE Hybrid, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS
View related parts
Ford Fusion Diagnostic Module Part Number: AE5Z-14B321-B
$276.39 MSRP: $379.21
You Save: $102.82 (28%)
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly - Airbag; Air Bag Control Module; Diagnostic Unit
- Replaces: 9E5Z-14B321-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford Fusion | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Fusion Diagnostic Module Part Number: AE5Z-14B321-A
$437.13 MSRP: $685.37
You Save: $248.24 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly - Airbag; Air Bag Control Module; Diagnostic Unit
- Replaces: 9E5Z-14B321-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010 Ford Fusion | S, SE, SEL, Sport | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Side Impact Sensor Part Number: 9E5Z-14B345-A
$30.33 MSRP: $41.27
You Save: $10.94 (27%)
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Impact Sensor; Air Bag Sensor; Side Sensor
- Replaces: 6E5Z-14B345-AA, 8E5Z-14B345-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Pressure Sensor, Center Part Number: HS7Z-14B345-AA
$72.03 MSRP: $110.85
You Save: $38.82 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Side Air Bag; Air Bag Seat Sensor Mat, Center; Air Bag Impact Sensor, Center; Air Bag Sensor; Side Impact Sensor; Side Sensor
- Position: Center
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Front Sensor Part Number: 9E5Z-14B004-A
Product Specifications
- Other Name: Sensor Assembly; Air Bag Sensor
- Position: Front
- Replaces: 8E5Z-14B004-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Front Sensor Part Number: 6E5Z-14B004-A
Product Specifications
- Other Name: Sensor Assembly; Air Bag Impact Sensor, Front; Air Bag Sensor
- Position: Front
- Replaces: 6E5Z-14B004-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2009 Ford Fusion | S, SE, SEL | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

Ford Fusion Air Bag Sensor

OEM Air Bag Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Air Bag Sensor with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Air Bag Sensor plays an important role in protecting the customers and reliability of the Ford Fusion automobiles. A major feature of this model is a crash sensor that detects an impact and initiates the control unit to release the air bags to further improve the level of protection of the occupants in the event of an accident. As a performance car, the Air Bag Sensor has been instituted to address crash force so as to elicit an air bag in the right sense of time. Its compatibility can reach multiple Ford Fusion, preserving a purpose of a similar model since the car model's creation in 2005. This reliability has made the Ford Fusion one of the most safe choices that a consumer can embark on in the middle size vehicles segment. Air Bag Sensor is not only essential for safety but also calls for promulgating the efficiency of Ford Fusion while synchronizing it with the new safety features. Air Bag Sensor has some unique traits that distinguish it from competitors: it has a very reactive and rather simple design. Thus, in such segments as safety, the Ford Fusion has been proven to be better than rivals such as the Toyota Camry and Honda Accord due to its performance of an Air Bag Sensor. Indeed, a closer look at the Air Bag Sensor reveals that Ford is highly safety conscious and this is evident in the Performance of the vehicles it offers to the market and thus Ford deserves to be considered by anyone who wants to own a safe car to drive.

Ford Fusion Air Bag Sensor Parts and Q&A

Front Sensor
9E5Z-14B004-A
Q: What are the crucial steps to take when servicing the front Air Bag Sensor involved in a crash on Ford Fusion?
A:
Before servicing the front impact severity sensor one should check the restraints control module (RCM) as well as the impact sensor attachment points for deformities if the vehicle suffered crash damage. All production specifications for damaged areas should be restored to their original state before installing new RCM components and sensors without exception because inadequate installation could result in fatalities or severe injuries in a car accident. The restraints control module indicator should light up when the RCM fuse is removed while the ignition switch is ON because this represents correct behavior with no issues in the supplemental restraint system (SRS). A vehicle cannot be released for market unless the supplemental restraint system completes all operational checks with no detected faults. The diagnostic process requires part replacement as a first step towards repair; reinstalling the original part should follow and the diagnostic procedure must be executed again. Your first step should be to disable the SRS system before removing the 2 bolts along with 2 pin-type retainers from the upper grille. Operation of the restraint systems depend on tight fastener torque to correct specifications. Both components need thorough cleaning with no residue allowed prior to installing the front impact severity sensor and bracket assembly. Make note of the locator tab position for its later reinstallation. To proceed with this operation gently move the upper grille forward before removing the bolt securing the front impact severity sensor assembly while disconnecting its electrical connector for final removal of the assembly. First secure the bolt to 12 Nm (9 lb-ft) torque specification then enable SRS functions as the last step for installation.
Side Impact Sensor
9E5Z-14B345-A
Q: How to service the Air Bag Sensor located in the B-pillar on Ford Fusion?
A:
Service of the B-pillar side impact sensor begins with disabling the SRS system. The service begins by removing scuff plate trim pieces from both front and rear doors before sliding down the lower B-pillar trim to detach it from the upper B-pillar trim. Cut the electrical wire connection of the side impact sensor. The restraints control module RCM along with the impact sensor require proper torque tightening because this action improves restraint system performance which reduces crash-related injuries. Clean the mating surfaces on the B-pillar joint with side impact sensor while removing any foreign matter. Document the sensor position and its locating tab before reinstalltion. The bolt and side impact sensor need removal before installing a new sensor which must get tightened to 12 Nm (9 lb-ft). Repeated steps in reverse order will enable the installation of components followed by restart of SRS operation.