How to remove and replace the front bumper cover on Ford Expedition?

The removal process starts by dismantling the three lower air deflector pin-type retainers from their positions while setting the deflector to the side. The process begins by taking out both lower retaining pins of the front bumper cover before unbolting the four retaining screws from the left and right splash shields. Remove the front bumper cover from the fenders using the four retaining bolts after which installation requires screw torquing at 11 Nm (8 lb-ft). The installation requires disconnecting fog lamps electrical connectors on both left and right sides when fog lamps are present in the vehicle. First remove the upper air deflector through ten pin-type retainer removal before removing two upper pin-type retaining mechanisms for the lower air deflector. The four bolts which secure the grille-to-radiator support should be removed after bracket separation followed by front bumper cover detachment. The new bumper cover must be fitted by repeating the steps for removal in the reverse order.

How to service and repair the front bumper cover on Ford Expedition?

Workers must start front bumper cover servicing and repairs on Expedition and Navigator vehicles by taking out the lower air deflector that uses eight pin-type retainers for attachment. The service and repair of the front bumper cover begins by uninstalling 2 lower pin-type retainers followed by separating the 3 screws from the front fender splash shield and disconnecting the 2 bolts that join the front fender to the front bumper cover. Reinstallation of these bolts requires a torque of 8 Nm (71 lb-in). The upper air deflector removal starts with disconnecting the fog lamp electrical connectors before moving to 8 pin-type retainer removal then finishing with 2 more bolts. Free the retaining clips of the front bumper cover before extracting it. The Navigator requires the same procedures as the Expedition to remove its fog lamp electrical connectors while dropping the clips and separating the front bumper. The installation procedure becomes completed by performing the removal steps in reverse order.

OEM Ford Expedition Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

68 Bumpers found

View related parts
Ford Expedition Impact Bar, Rear Part Number: 7L1Z-17906-B
$214.80 MSRP: $315.42
You Save: $100.62 (32%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Impact Bar, Rear; Reinforcement
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2017 Ford Expedition | EL Eddie Bauer, EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Upper Cover, Front Part Number: FL1Z-17D957-BPTM
$744.76 MSRP: $1103.35
You Save: $358.59 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front Upper
- Manufacturer Note: Paint to match
- Position: Front Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Expedition | EL King Ranch, EL Limited, EL Platinum, EL XL, EL XLT, King Ranch, Limited, Platinum, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Impact Bar, Rear Part Number: 7L1Z-17906-C
$505.76 MSRP: $742.67
You Save: $236.91 (32%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Cover Reinforcement Beam, Rear; Bumper Impact Bar, Rear; Reinforcement
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2017 Ford Expedition | Eddie Bauer, Funkmaster Flex Edition, King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Impact Bar, Front Part Number: YL3Z-17757-CAA
$290.34 MSRP: $362.07
You Save: $71.73 (20%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Face Bar, Front; Bumper
- Position: Front
- Replaces: XL3Z-17757-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2002 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Lower Cover, Front Part Number: FL1Z-17D957-CPTM
$451.17 MSRP: $707.38
You Save: $256.21 (37%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2017 Ford Expedition | EL King Ranch, EL Limited, EL Platinum, EL XL, EL XLT, King Ranch, Limited, Platinum, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Bumper Cover, Charcoal Black, Rear Part Number: BL1Z-17K835-HA
$139.16 MSRP: $202.57
You Save: $63.41 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Charcoal Black
- Position: Rear
- Replaces: BL1Z-17K835-HPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2017 Ford Expedition | King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX
View related parts
Ford Expedition Bumper Cover, Rear Part Number: JL1Z-17K835-AEPTM
$505.76 MSRP: $742.67
You Save: $236.91 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Cover, Rear
- Position: Rear
- Replaces: JL1Z-17K835-APTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford Expedition | King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Lower Cover Part Number: NL1Z-17K835-BAPTM
$305.70 MSRP: $448.90
You Save: $143.20 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2024 Ford Expedition | King Ranch, Limited, Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT, Platinum, SSV, Timberline, XL, XL STX, XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Lower Cover Part Number: NL1Z-8419-GBPTM
$241.72 MSRP: $354.95
You Save: $113.23 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Moulding
- Replaces: NL1Z-8419-GAPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2024 Ford Expedition | King Ranch, Max King Ranch | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Bumper Cover, Rear Part Number: JL1Z-17K835-DCPTM
$514.09 MSRP: $754.90
You Save: $240.81 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Replaces: JL1Z-17K835-EPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford Expedition | Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Bumper Cover, Rear Part Number: JL1Z-17K835-FPTM
$400.18 MSRP: $587.63
You Save: $187.45 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Paint to match
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford Expedition | King Ranch, Limited, Platinum, SSV, XL, XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Bumper Cover, Charcoal Black, Rear Part Number: BL1Z-17K835-KA
$257.21 MSRP: $377.70
You Save: $120.49 (32%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: Charcoal Black
- Position: Rear
- Replaces: BL1Z-17K835-KPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2017 Ford Expedition | EL King Ranch, EL Limited, EL Platinum, EL SSV, EL XL, EL XLT | 6 Cyl 3.5 L GAS, 8 Cyl 5.4 L FLEX
View related parts
Ford Expedition Bumper, Front Part Number: XL3Z-17757-AA
$324.68 MSRP: $476.77
You Save: $152.09 (32%)
ADD TO CART
Product Specifications
- Other Name: Bumper Face Bar, Front
- Manufacturer Note: Chrome - bar only
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2002 Ford Expedition | Eddie Bauer, XLT | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Bumper Cover, Front Part Number: 4L1Z-17D957-EAA
$384.72 MSRP: $564.93
You Save: $180.21 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2006 Ford Expedition | Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Bumper Cover, Rear Part Number: 4L1Z-17K835-BAA
$450.75 MSRP: $661.90
You Save: $211.15 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Ford Expedition | Eddie Bauer, Limited, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Lower Cover, Front Part Number: 7L1Z-17D957-AA
$188.93 MSRP: $275.00
You Save: $86.07 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Cover, Front Lower
- Position: Front Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2014 Ford Expedition | Eddie Bauer, EL Eddie Bauer, EL King Ranch, EL Limited, EL XL, EL XLT, Funkmaster Flex Edition, King Ranch, Limited, XL, XLT | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Bumper Cover Part Number: NL1Z-17K835-BBPTM
$736.57 MSRP: $1091.22
You Save: $354.65 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover
- Replaces: NL1Z-17810-MCPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2024 Ford Expedition | Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XLT | 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Bumper Cover, Front Part Number: 4L1Z-17D957-HAA
$319.98 MSRP: $469.87
You Save: $149.89 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2006 Ford Expedition | Eddie Bauer, Limited, XLS, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
Ford Expedition Bumper Cover, Rear Part Number: JL1Z-17K835-DB
$537.46 MSRP: $789.22
You Save: $251.76 (32%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Cover, Rear
- Position: Rear
- Replaces: JL1Z-17K835-DPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford Expedition | Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT | 6 Cyl 3.5 L GAS
View related parts
Ford Expedition Bumper Cover, Rear Part Number: JL1Z-17K835-BBPTM
$565.07 MSRP: $837.13
You Save: $272.06 (33%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Rear; Bumper Cover, Rear
- Position: Rear
- Replaces: JL1Z-17K835-BPTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford Expedition | Max King Ranch, Max Limited, Max Platinum, Max SSV, Max XL, Max XLT | 6 Cyl 3.5 L GAS

| Page 1 of 4 |Next >

1-20 of 68 Results

Ford Expedition Bumper

OEM Bumper boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper with long life and a perfect fit. Come to our website and find genuine Ford Expedition parts. We keep a wide inventory of OEM Expedition parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Expedition Bumper Parts and Q&A

Upper Cover, Front
7L1Z-17D957-APTM
Q: How to remove and replace the front bumper cover on Ford Expedition?
A:
The removal process starts by dismantling the three lower Air Deflector pin-type retainers from their positions while setting the deflector to the side. The process begins by taking out both lower retaining pins of the front bumper cover before unbolting the four retaining screws from the left and right splash shields. Remove the front bumper cover from the fenders using the four retaining bolts after which installation requires screw torquing at 11 Nm (8 lb-ft). The installation requires disconnecting fog lamps electrical connectors on both left and right sides when fog lamps are present in the vehicle. First remove the upper air deflector through ten pin-type retainer removal before removing two upper pin-type retaining mechanisms for the lower air deflector. The four bolts which secure the grille-to-radiator support should be removed after bracket separation followed by front bumper cover detachment. The new bumper cover must be fitted by repeating the steps for removal in the reverse order.
Bumper Cover, Front
4L1Z-17D957-EAA
Q: How to service and repair the front bumper cover on Ford Expedition?
A:
Workers must start front bumper cover servicing and repairs on Expedition and Navigator vehicles by taking out the lower Air Deflector that uses eight pin-type retainers for attachment. The service and repair of the front bumper cover begins by uninstalling 2 lower pin-type retainers followed by separating the 3 screws from the front fender splash shield and disconnecting the 2 bolts that join the front fender to the front bumper cover. Reinstallation of these bolts requires a torque of 8 Nm (71 lb-in). The upper air deflector removal starts with disconnecting the fog lamp electrical connectors before moving to 8 pin-type retainer removal then finishing with 2 more bolts. Free the retaining clips of the front bumper cover before extracting it. The Navigator requires the same procedures as the Expedition to remove its fog lamp electrical connectors while dropping the clips and separating the front bumper. The installation procedure becomes completed by performing the removal steps in reverse order.